welcome to Shenzhen Fortunecome Technology Co,.Ltd.

You are here:Home > Water Flosser > Then xiyaqi

V6


Parameters

Charger input: AC -

Charger output: v 300 ma

Built-in charging battery: aa lithium ion battery. 1,700 maleic

The battery is fully charged for eight hours

Battery cycle charging: > 500 cycles

Each time full of electricity: 60 minutes. .

Water pressure: > 120 psi

Pump water frequency: 1600 / minutes

Noise: not more than 75 db ( a )

Tank capacity: 200 ml

Product size: 71 * 55 * 142 mm

Product weight: n

Color box dimensions: 164 * 83 * 250 mm

Each set weight: 540 / set

Carton dimension: 43.5 * 34.5 * 51 cm ( 20 PCs / box )

N. w.: 10

G.: 12


Configure

Accessories:

1 host 1, 2 nozzle, 1 charger. 1 USB line, 1 instruction

Introduction

Fl V5 is designed to protect dental and gum health and health care products.


2.1 the advanced electronic control system makes the operation more simple and convenient.


2.2 the strong and pulsating water spray can flush the toothbrush where the toothbrush can not be brushed.


2.3 gently pulsating water spray can gently massage the gum, making teeth healthier.


2.4 two kinds of working mode ( normal standard, soft gentle ) corresponds to two modes indication point.


2.5 ren nozzle design, use more comfortable.


The 2.6 with recognizable Decorative ring nozzles to achieve the function of a multi-purpose use.


2.7 rechargeable use, environmental protection.


Iii. product identification


Iv. product overview:


3.1 fl - V5 switch is pushed up a lattice. This is the gentle gear, and then pushed to the dingge. For the standard gear. Pull back the bottom to shutdown status.


3.2 fl - V5 requires the use of a matching charger ( input: 100 vac, output: 5.0 VDC ( kongfu v ) 300 ma ~ 1 a ) to charge, chongbao time for approximately 8 h ( 7 1h )


3.3 do not trigger the switch during working, and will shut down automatically in 2 minutes.



Ⅲ performance


Regular indicators:


1. seal test ( only for the part of the oral irrigator body shall meet the ipx7 standard, and meet any of the following shall be qualified ):


Immersion or bubble water test: the test prototype is placed in 1m deep in water, the test time is 30 minutes. There is no water stain.


2. the host noise is less than 77 db ( loop mirror noise 49 db, zhujili db test head 10 cm, pumping test ).


3. wear resistance test:


3.1 the surface of the product shall be scratch with jiedao, and then the screen printing screen shall be torn up, and the screen printing screen printing shall not exceed 5 %.


3.2 industrial alcohol, after a cycle wipe, screen printing ink screen.


4. high voltage test ( only for the electric source part of the open switch ):


Gao Yayi output voltage of ac3000v, leakage current 5 ma, test time 3 seconds.


Second, life test:


1. the plug of the switching power supply plug: after the circular unplugging, the function is normal and the pulling force reaches the requirements.


2. switch life test: put the product on the life test rack of the button, after testing the specified number of switch buttons, the switch button should work.


Product appearance inspection requirements and packing:


1. each rubber parts can not have excessive flash, mixing color, Light stock and white hat, injection and other defects, and the nozzle shall be smooth.


2. finished product packaging does not allow for stains, damage, scratches, scratches, scratches, rupture, excessive flash, nozzle and whitening.


3. finished product packaging must be printed perfect, no damage, stain, fingerprint, etc., the standard of packing quantity.